Frequently Asked Questions
FAQ
Toy Hauler Fuel Station
Click this link for the video guide. Control Panel Operation
- Low or no fuel in the tank
- Toy-Hauler not level on the ground
- Panel not programmed correctly, click this link for video guide. Single System Control Panel Programing
- Test your sending unit for Ohmโs reading, click this link for video guide. Sending Unit Ohms Test
- Low or no fuel in the tank
- Toy-Hauler not level on the ground
- Panel not programmed correctly, click this link to video guide. Dual System Control Panel Programming
- Test your sending units for Ohmโs reading, click this link for video guide. Sending Unit Ohms Test
- Low or no fuel in tank
- Toy-Hauler not level on the ground
- Panel not programmed correctly, click this link for video guide. Generator Only Control Panel Programming
- Test the sending unit for Ohmโs reading, click this link for the video guide. Sending Unit Ohms Test
Check wiring harness for power, click this link for video guide. How to test Fuel Station for power
After checking for power, if the control panel does not power on (no visible lights), the panel may need to be replaced.
Replacement control panels available by clicking this like. Control Panels
Check pump harness for 12 Volt power. Click this link for guide guide. Pump Harness 12 Volt Test
- If pump is not receiving 12 Volt power, check inline fuse on the pump wire and fuse at the power supply.
- If pump is not receiving 12 Volt power, check power supply to ensure wiring is correctly installed on the fuel system circuit
Remove pump gears. Click this link for video guide. ECI5 Pump Gear Test
- If pump powers on with no gears, this means your pump is working but you may need to clean or replace your worn gears. You can purchase replacement gears here. Pump Accessories
- If pump does not turn on after gear removal, check to make sure your pump has power. If your pump is receiving 12 Volts+ but not turning on, replace pump. Pump replacements available here. Pump Accessories
- Check for blockage between the filler neck and tank manifold.
- Tank was not installed at the correct height at the factory.
- If you are experiencing spit back when you fill your tank, your fill hose between the fill neck and fuel tank may not be at a proper angle to allow flow.
- If your unit is still under warranty, please contact your toy hauler manufacturer.
- Ensure your fuel tank has enough fuel to pick up to prime the generator
- Check all fuel lines between generator and fuel tank to ensure there are no kinks.
- Check generator internal fuel pump
- Your fuel system can be operated with the designated fuel marked on your fuel system.
- **FOR UNITS WITH A GENERATOR, PLEASE CONSULT YOUR MANUAL TO ENSURE YOU ARE USING THE CORRECT FUEL TYPE DESGINATED FOR YOUR GENERATOR.
- **E85 FUEL SHOULD NEVER BE USED IN AN ECI / VECTOR FUEL SYSTEM
The OEM has designed your toy hauler to NFPA 1192 standards, this includes the position and length in which the 3/4โณ nozzle hose has been installed. It is not recommended you change your nozzle hose for a longer length.
ECI does not recommend installing an automatic nozzle on your toy hauler fuel station.
Click link for maintenance guide for your toy hauler fuel station. Maintenance Guide
Click this link for warranty information. Warranty
Truck Transfer Tanks
- The ELITE line can legally transport gasoline (DOT Compliant), comes fully assembled from the factory with an 8 GPM GPIยฎ pump, digital control panel with gauge, built in filter bowl, 12-foot dispensing hose and manual nozzle.
- Both PRO and Elite series can hold diesel fuel and are made of 11-gauge American steel.
- The ELITE series comes with everything you will need to begin fueling your applications, no additional parts are required for purchase.
- The PRO series includes all mounting hardware to install your tank including a mechanical gauge, vent valve and SpinSecureยฎ locking fuel cap. A pump of your choosing is available for purchase if required. A meter option is also available if needed.
- Click this link for the video guide to install your PRO System. PRO Installation
- Click this link for the video guide to install your ELITE System. ELITE Installation
Use this guide to determine the correct tank for your truck. Tank Fitment Guide
Use this guide to get an accurate gallon reading on your gauge. Gallons reading Guide
Click this link for warranty information. Warranty
You can find your local dealer or up-fitter by clicking this link. Dealer Locator
All our transfer tanks are designed, manufactured and assembled in USA, at our Upland, Ca factory.
Click this link for maintenance guide. Elite maintenance
To download the most recent DOT permit please click this link. DOT
Tool Boxes
Use this guide to determine which toolbox fits your truck. Toolbox Fitment Guide (COMING SOON)
- Click this link for the video guide to install your Cross-Cab box. COMING SOON
- Click this link for the video guide to install your Chest box. COMIN SOON
Click this link for the video guide to install your puck lock shroud. COMING SOON
- To download the manual click here. COMING SOON
No, but Vector partners with many distributors/outfitters that can install your Vector Tool Box.
You can find your local dealer or up-fitter by clicking this link. Dealer Locator
Yes! Please click this link for our toolbox parts page. (coming soon)
Yes, contact support and give us your current key code. support@vectorperformance.com
No, Vector does not currently take requests for custom sizes or custom colors.
All our transfer tanks are designed, manufactured and assembled in USA, at our Upland, Ca factory.